BS ISO 5611-2 pdf free download

BS ISO 5611-2 2015 pdf free download.Cartridges, type A, for indexable inserts Part 2: Style F.
This part of this ISO 5611 applies for cartridges type A, with hole(s) for fastening screw(s), of style F, i.e. with cutting edge angle κ r = 90° for end cutting. Cartridges are intended to be used with indexable inserts made of hard metal, ceramic, or other cutting materials and are primarily mounted to be used for internal turning of operations.
2Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1832, Indexable inserts for cutting tools — Designation ISO 5608, Turning and copying tool holders and cartridges for indexable inserts — Designation
ISO 5611-1, Cartridges, type A, for indexable inserts — Part 1: General survey, correlation and determination of dimensions
3 Dimensions Cartridges type A need not comply with the pictorial representation, only the dimensions given shall be observed. For determination of dimensions h 1 , f and l 1 see ISO 5611-1. For explanation of the designation code for cartridges, see ISO 5608.
4 Designation
A cartridge in accordance with this part of ISO 5611 shall be designated by:
a) “Cartridge”;
b) reference of this part of ISO 5611, i.e. ISO 5611-2;
c) letter symbol identifying the method of holding the insert, in accordance with ISO 5608;
d) letter symbol identifying insert shape, in accordance with ISO 1832;
e) letter symbol identifying cartridge style, in accordance with ISO 5608;
f) letter symbol identifying insert normal clearance, in accordance with ISO 1832;
g) letter symbol identifying hand of cartridge, in accordance with ISO 5608;
h) number symbol identifying tool height (shank height of cartridges and height of cutting edge), in accordance with ISO 5608;
i) number symbol identifying tool holder shank width or, for cartridges, letter C followed by a letter symbol identifying the cartridge type, in accordance with ISO 5608;
j) letter symbol identifying tool length, in accordance with ISO 5608;
k) number symbol identifying indexable insert size, in accordance with ISO 1832.
EXAMPLE Cartridge with screw clamping through hole (S) triangular indexable insert shape (T), cartridge style F (F), for the insert normal clearance 7° (C), right hand cartridge (R), with height h 1 = 12 mm (12), cartridge Type A (CA), length l 1 = 55 mm (–), edge length l 4 = 16,5 mm (16) is designated as follows: Cartridge ISO 5611–2 – STFCR 12CA – 16
5 Material
Steel with a tensile strength of at least 1 200 N/mm 2 .
6 Design
6.1 Method of holding
(first letter symbol identifying the method of holding the insert)
6.1.1 Cartridge for indexable inserts with insert normal clearance α n = 7°
(fourth symbol identifying insert normal clearance C)
— holding screw clamping through hole; letter symbol S, e.g. SCFCR.
6.1.2 Cartridge for indexable inserts with insert normal clearance α n = 7°
(fourth symbol identifying insert normal clearance C)
— holding screw clamping through hole; letter symbol S, e.g. SCFCR.
6.1.3 Cartridge for indexable inserts with insert normal clearance α n = 0°
(fourth symbol identifying insert normal clearance N)
— holding with hole clamping; letter symbol P, e.g. PTFNR.
6.2 Corner radius r ε
Cartridges in accordance with this part of ISO 5611 can be equipped with indexable inserts with cutting edge lengths l 4 as specified in Table 1 and any corner radius r ε .
The values for f given in Table 1 apply to cartridges with indexable inserts having corner radii r ε in accordance with Table 2.
For cartridges with indexable inserts with corner radii other than those specified in Table 2, the dimensions of f shall be determined in accordance with ISO 5611-1.
The tolerances on h 1 and f refer to dimensions measured with master indexable insert and master shim, if any.BS ISO 5611-2 pdf download.