BS EN IEC 63171-1 pdf free download

BS EN IEC 63171-1-2020 pdf free download.Connectors for electrical and electronic equipment – Part 1: Detail specification for two-way, shielded or unshielded, free and fixed connectors – Mechanical mating information, pin assignment and additional requirements for Type 1 copper LC style (IEC 63171-1:2020).
This part of IEC 631 71 covers two-way, shielded or unshielded, free and fixed connectors for data transmission with frequencies up to 600 MHz and with current carrying capacity up to 2,0 A at 60 °C. It is intended to specify the common dimensions, mechanical, electrical, signal integrity, environmental characteristics, reliability specifications and corresponding tests for these connectors.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the reference document (including any amendments) applies.
IEC 60050-581 , International Electrotechnical Vocabulary (IEV) – Chapter 581:Electromechanical components for electronic equipment
IEC 60068-1 , Environmental testing – Part 1: General and guidance
IEC 6051 2-1 , Connectors for electrical and electronic equipment – Tests and measurements –Part 1: Generic specification
IEC 6051 2-1 -1 , Connectors for electronic equipment – Tests and measurements – Part 1-1:General examination – Test 1a: Visual examination
IEC 6051 2-1 -2, Connectors for electronic equipment – Tests and measurements – Part 1-2: General examination – Test 1b: Examination of dimension and mass
IEC 6051 2-2-1 , Connectors for electronic equipment – Tests and measurements – Part 2-1:Electrical continuity and contact resistance tests – Test 2a: Contact resistance – Millivolt level method
IEC 6051 2-2-5, Connectors for electronic equipment – Tests and measurements – Part 2-5: Electrical continuity and contact resistance tests – Test 2e: Contact disturbance
IEC 6051 2-3-1 , Connectors for electronic equipment – Tests and measurements – Part 3-1: Insulation tests – Test 3a: Insulation resistance
IEC 6051 2-4-1 , Connectors for electronic equipment – Tests and measurements – Part 4-1: Voltage stress tests – Test 4a: Voltage proof
IEC 6051 2-5-2, Connectors for electronic equipment – Tests and measurements – Part 5-2:Current-carrying capacity tests – Test 5b: Current-temperature derating
IEC 6051 2-6-4, Connectors for electronic equipment – Tests and measurements – Part 6: Dynamic stress tests – Section 5: Test 6d: Vibration (sinusoidal)
IEC 6051 2-9-1 , Connectors for electronic equipment – Tests and measurements – Part 9-1: Endurance tests – Test 9a: Mechanical operation
IEC 6051 2-1 1 -7, Connectors for electronic equipment – Tests and measurements – Part 11-7: Climatic tests – Test 11g: Flowing mixed gas corrosion test
IEC 6051 2-1 1 -1 2, Connectors for electronic equipment – Tests and measurements – Part 11- 12: Climatic tests – Test 11m: Damp heat, cyclic
IEC 6051 2-1 3-2, Connectors for electronic equipment – Tests and measurements – Part 13-2: Mechanical operation tests – Test 13b: Insertion and withdrawal forces
IEC 6051 2-1 5-6, Connectors for electronic equipment – Tests and measurements – Part 15-6: Connector tests (mechanical) – Test 15f: Effectiveness of connector coupling devices
IEC 6051 2-25-9, Connectors for electronic equipment – Tests and measurements – Part 25-9: Signal integrity tests – Test 25i: Alien crosstalk
IEC 6051 2-26-1 00, Connectors for electronic equipment – Tests and measurements – Par 26-100: Measurement setup, test and reference arrangements and measurements for connectors according to IEC 60603-7 – Tests 26a to 26g
IEC 6051 2-28-1 00, Connectors for electrical and electronic equipment – Tests and measurements – Part 28-100: Signal integrity tests up to 2 000 MHz – Tests 28a to 28g
IEC 60664-1 , Insulation coordination for equipment within low-voltage systems – Part 1: Principles, requirements and tests
IEC 621 53-4-1 2, Metallic communication cable test methods – Part 4-12: Electromagnetic
compatibility (EMC) – Coupling attenuation or screening attenuation of connecting hardware – Absorbing clamp method
IEC 621 53-4-1 5, Metallic communication cable test methods – Part 4-15: Electromagnetic compatibility (EMC) – Test method for measuring transfer impedance and screening attenuation – or coupling attenuation with triaxial cell
ISO/IEC 11801-1, Information technology – Generic cabling for customer premises – Part 1:General requirements
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60050-581 and IEC 6051 2-1 apply.
ISO and IEC maintain terminology databases for use in the standardization at the following addresses:
• IEC Electropedia: available at http://www.electopedia.org
• ISO Online browsing platform: available at http://www.iso.org/obp.BS EN IEC 63171-1 pdf download.