BS EN 1501-5 pdf free download

BS EN 1501-5:2021 pdf free download.Refuse collection vehicles – General requirements and safety requirements Part 5: Lifting devices for refuse collection vehicles.
S Safety requirements and/or protective measures
5.1 General
5.1.1 Introduction
Lifting devices shall comply with the safety requirements and/or protective measures of this clause. In addition, the lifting devices shall be designed according to the principles of EN ISO 12100:2010 for relevant but not significant hazards which are not dealt with by this standard. All systems and components shall be specified and installed in accordance with their manufacturer’s instructions.
Intercompatibility between RCV and interchangeable refuse container lifting device shall be ensured. All mechanical, electrical, pneumatic and hydraulic interfaces shall be available.
If different lifter systems are combined, the requirements specific for these systems shall be considered. 5.1.2 Design
5.1.2.1 General
Any crushing and shearing hazards shall be avoided or minimized by design according to EN ISO 13857:2019 and EN ISO 13854:2019 or appropriate guard(s) according to EN ISO 14120:2015 or safeguards according to EN ISO 13855:2010.
The design shall take into account the dynamic impact of the lifting device on the connection between the refuse container lifting device and the body of the RCV.
5.1.2.2 Distance to the ground
To prevent foot injuries, automatic or semi-automatic downwards movements shall be stopped automatically when the distance between the lower edge of the lifting carriage and the level on which the RCV is standing shall be at least 120 mm or 320 mm for lifting carriage which can operate on the kerbside.
If movement of the lifting carriage down to the ground level is necessary, the distance between 120mm (320 mm) and the horizontal ground shall be controlled by a hold-to-run control device situated in a position where the lifting carnage is in full view of the operator.
The control of the movement of the lifting carriage to the clearance position is allowed from the driver’s position under the following conditions
— max. lifting movement is limited to 400 mm from the lowest possible position of the lifting carriage;
— any crushing and shearing risk is prevented;
— automatic lifting is possible only after the RCV has started moving.
5.1.2.3 Hopper
The loading edge of the refuse container lifting device and/or the body shall be designed taking into consideration the volume of the largest designated refuse container emptied by the refuse container lifting device and the volume of the hopper, in order to avoid refuse falling out of the hopper.
When the hopper is emptied by the compaction mechanism at the same time as the refuse container lifting device is being operated, the design shall be such that the designated refuse container shall not collide with it.
5.1.2.4 Load
The refuse container lifting device shall be provided with a device preventing emptying in excess of the maximum permissible load of the largest designated refuse container.
The maximum working load for the lifting device is the weight of the largest designated refuse container pIus 1,1 times its nominal load. This shall be applied at the centre of gravity of the largest fully loaded refuse container.
The nominal load of the loaded refuse container is determined assuming a density of refuse as defined in the standards of EN 840:2020 (all parts), EN 12574:2017 (all parts) or EN 13071:2019 (all parts).
5.1.2.5 Tests
The functional dynamic test load shall be 1,1 times the maximum working load for lifting up and down in the nominal cycle time. The functional static test load shall be 1,25 times the maximum working load.
5.1.2.6 Guide system
The pick-up system shall be provided with a guide system to laterally position the designated refuse container on the refuse container lifting device.
5.1.2.7 Locking system
The designated refuse container shall be kept locked during the emptying cycle of the lifting device above a tilt angle of 45° from the vertical or 2 000 mm above the ground, even if electric, hydraulic or pneumatic energy fails.
In the automatic or semi-automatic lifting mode, it shall be detected that the designated refuse container is locked in position. Detection is only required for locking systems directly actuated by electric, hydraulic and/or pneumatic energy. The detection device shall fulfil required performance level PLr d according to EN ISO 13849-1:2015, as defined in 5.10.1.
5.1.2.8 Speed and acceleration
The minimum emptying cycle time, the maximum peripheral speed and the maximum acceleration of the lifting device shall comply with the requirements in the following table depending on the type of lifting device and the designated refuse container capacity.BS EN 1501-5 pdf download.